USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for...
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com...
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fi re, electric shock or damage.
Page 6
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fi re, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
WARNING If you drop any materials or liquids such as water into the monitor when cleaning, unplug the power cable immediately and contact your dealer or iiyama service center. NOTE To protect the Touch screen surface, do not scratch or rub the screen with a hard object.
CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama offi ce.
CONTROLS AND CONNECTORS <Front> <Back> Menu Button ( Scroll Up / Brightness Button ( Scroll Down / Mute Button ( Select / Auto Button ( Power Switch ( Keyhole for Security Lock You can fasten a security lock and cable to prevent the monitor from being removed NOTE without your permission.
An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard connector. If a special cable is required please contact your local iiyama dealer or regional iiyama offi ce.
Change to the desired signal timing listed on page 32: COMPLIANT TIMING. Windows XP/Vista/7/8/8.1/10 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows XP/Vista/7/8/8.1/10 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 32. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 15 for SCREEN ADJUSTMENTS.
ADJUSTMENT MENU CONTENTS CONTRAST BRIGHTNESS 1 2 80 x 1 0 2 4 FH: 63 KHz FV: 59.9 Hz Adjustment Item Problem / Option Button to Press Too dull CONTRAST Too intense Too dark Direct BRIGHTNESS * Too bright * Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright.
Page 15
A UTO A D J U ST Only Analog Input H -P OSIT I ON V- P OSIT I ON H - SIZ E FI N E Adjustment Item Problem / Option Button to Press Direct Adjust H/V-POSITION, H-SIZE and FINE automatically. AUTO ADJUST * Too left H-POSITION...
Page 16
O SD H-POSIT ION O SD V-POSIT ION OSD TIMEOUT RESET INP UT SEL ECT Adjustment Item Problem / Option Button to Press OSD is too left OSD H-POSITION OSD is too right OSD is too low OSD V-POSITION OSD is too high You can set the OSD display duration time OSD TIMEOUT between 5 and 60 seconds.
Page 17
ENGLISH ESPAÑOL FRANÇAIS DEUTSCH ITALIANO Adjustment Item Problem / Option Button to Press ENGLISH English ESPAÑOL Spanish Japanese FRANÇAIS French OSD LANGUAGE DEUTSCH German Traditional Chinese Simplifi ed Chinese ITALIANO Italian 9300 6500 5500 GREEN 7500 BLUE USER Adjustment Item Problem / Option Button to Press 9300...
Page 18
VOLUME MUTE OFF Adjustment Item Problem / Option Button to Press Too soft VOLUME Too loud Turn off the sound temporarily. MUTE Direct Return the sound volume to the previous level. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations.
If the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.com). Adjust the image by following the procedure below to get the desired picture.
Page 20
Press the Button. (AUTO ADJUST) Adjust the image manually by following procedure below when the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust. Adjust the V-POSITION so that the top and bottom of the picture frame will fit to the display area.
Page 21
Adjust the FINE to correct horizontal wavy noise, fl icker or blur in the zebra pattern. In case the strong fl icker or blurs remain on a part of the screen, repeat steps NOTE because the H-SIZE may not be adjusted correctly. If the fl icker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from again.
POWER 2W or 3W* 100% CONSUMPTION * ProLite T1531SR / ProLite T1731SR / ProLite T1931SR / ProLite T1532SR:2W ProLite T1531SAW / ProLite T1731SAW / ProLite T1931SAW:3W NOTE Even when using the power management mode, the monitor consumes electricity. Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption.
MONITOR or if the problem persists. 3. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance. Problem Check ...
RECYCLING INFORMATION For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com/recycle for monitor recycling. 20 RECYCLING INFORMATION...
APPENDIX SPECIFICATIONS : ProLite T1531SR Model Name ProLite T1531SR-B1 / ProLite T1531SR-W1 ProLite T1531SR-B1 A / ProLite T1531SR-W1 A Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15"...
Page 26
Model Name ProLite T1531SR-B3 / ProLite T1531SR-W3 Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×...
SPECIFICATIONS : ProLite T1531SAW Model Name ProLite T1531SAW-B1 / ProLite T1531SAW-W1 ProLite T1531SAW-B1 A / ProLite T1531SAW-W1 A Touch Technology Surface acoustic wave Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15"...
Page 28
Model Name ProLite T1531SAW-B3 / ProLite T1531SAW-W3 Touch Technology Surface acoustic wave Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15"...
SPECIFICATIONS : ProLite T1532SR Model Name ProLite T1532SR-B1 / ProLite T1532SR-W1 ProLite T1532SR-B1 A / ProLite T1532SR-W1 A Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size...
Page 30
Model Name ProLite T1532SR-B3 / ProLite T1532SR-W3 Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×...
SPECIFICATIONS : ProLite T1731SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 17" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H ×...
SPECIFICATIONS : ProLite T1731SAW Touch Technology Surface acoustic wave Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 17" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H ×...
SPECIFICATIONS : ProLite T1931SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H ×...
SPECIFICATIONS : ProLite T1931SAW Touch Surface acoustic wave Technology Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H ×...