Table of Contents
Advertisement
Quick Links
INSTALLATION MANUAL
MODEL #100398
50 IN. UNIvErSAL SNOw PLOw SySTEM
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
or visit championpowerequipment.com
SAvE THESE INSTrUCTIONS. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do
so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
EN
3759-M-IN
REV 20220606
Champion Power Equipment, Inc., Santa Fe Springs, CA USA
Advertisement
Table of Contents
Related Manuals for Champion 100398
Summary of Contents for Champion 100398
- Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. 3759-M-IN REV 20220606 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...
-
Page 2: Table Of Contents
TAbLE Of CONTENTS 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM TAbLE Of CONTENTS Introduction ........... Safety Definitions .......... Important Safety Instructions ....... Plow blade Installation ........Push Tube Assembly and Installation .... -
Page 3: Introduction
INTrODUCTION 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM SAfETy DEfINITIONS INTrODUCTION Congratulations on your purchase of a Champion Power Equipment The purpose of safety symbols is to attract your attention to (CPE) product. CPE designs, builds, and supports all of our possible dangers. -
Page 4: Important Safety Instructions
IMPOrTANT SAfETy INSTrUCTIONS 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM IMPOrTANT SAfETy INSTrUCTIONS PLOw bLADE INSTALLATION wArNING NOTICE Cancer and Reproductive Harm – www.P65Warnings.ca.gov Before starting the assembly of the blade and tubes see Hybrid Mount installation instructions to ensure it will work with your ATV. -
Page 5: Push Tube Assembly And Installation
PUSH TUbE ASSEMbLy AND INSTALLATION 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM 5. Tighten down all bolts. 2. Install angle lever assembly (B) to the tube weldment (8) as shown in Figure 5. Use the 5⁄16 x 1 in. (7.9 x 25.4 mm) standard carriage bolts (15.8) and 5⁄16 in. - Page 6 PUSH TUbE ASSEMbLy AND INSTALLATION 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM 5. Place washer bearing (14) into hole in blade gusset and 8. With springs installed and pitch blade under tension, install secure blade to tube system by fastening with the 1½ in.
-
Page 7: Hybrid Mount Installation Instructions
HybrID MOUNT INSTALLATION INSTrUCTIONS 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM GOOD BEST Figure 11-A - Blade Rotation Angle NOTICE Make sure handle is locked in before plowing. Figure 14 - Winch Line Angle 11. Attach the tube system to the Hybrid Mount System, by first... -
Page 8: Hybrid Mount Round Tube Frame Install
HybrID MOUNT rOUND TUbE frAME INSTALL 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM 2. The approximate distance that tab holes can be from the front NOTICE of the machine is 26 in. (66 cm) as shown in Figure 16. Every machine can vary because of ATV front contour. - Page 9 HybrID MOUNT SQUArE TUbE frAME INSTALL 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM 3. Place the Upper Mount Plate (2) over the frame at the location behind the tires where the frame widens out. Refer to Figure 20 for best fastener placement.
-
Page 10: Hybrid Mount Polaris ® Sportsman ® Install
HybrID MOUNT POLArIS® SPOrTSMAN® INSTALL 100398 - 50 IN. UNIvErSAL SNOw PLOw SySTEM HybrID MOUNT POLArIS ® 4. Loosely install the upper mount plate (2), 4 spacer plates (3) and lower mount plate (1) using the rubber spacers (4), SPOrTSMAN INSTALL ®... - Page 11 To complete registration you will need to include a copy of the – Problems caused by parts that are not original Champion purchase receipt as proof of original purchase. Proof of purchase Power Equipment parts.